I'd love some advice on repairing or replacing this bamboo cup lid, which has lasted around 5 years otherwise!

I've thought about doing a kintsugi type repair, since I still have the broken pieces: !

However, most kintsugi kits I've seen for sale online are either pretty expensive or not meant to be in contact with food. I'm cautious about using a cheaper epoxy for that reason as well -- I'm not sure how concerned I should be about chemicals leaching into my coffee even after it's cured.

Maybe I should just look for a replacement lid online? This one is about 9.5cm across, but I'm not sure they come in standard sizes

I was recently looking at old posts in this community, and it reminded me that it's been over a year since I repaired these two backpacks and made a few posts about the process.

Both of these have held up remarkable well in a year of near daily use. Some of the shoe-goo sealant is starting to detach in places: !

But most of it is still in place. The fabric patches and sewing line I used to close the rips are also still in one piece: ! !

The shoe goo is still in a drawer somewhere, so I may apply a fresh coat at some point, if more of it flakes off. But overall, I'm really happy with how these have held up!

This video made me think of this community. Fixing a camping chair and stool with Tyvek is pretty inventive, as well as sewing a tent with the material!

Hello! I have a sling bag that I really like, but the strap doesn't take it as close to my body as I would like. I have a sewing machine, but I have never used it for stitching seatbelt webbing. What sort of needle would I need to use, and which type of thread would be best suited for the material?

My dog chewed her harness. Here's the mending job. Mended with embroidery floss by hand.

Despite trying different fits and brands of pants, I keep running into the problem of them eventually getting holes in them, typically around the seams of the crotch where of course you least want them. The rest of the pants are generally fine, so it feels like a waste to toss them, but I'm not sure how well one might be able to fix such holes right along seams...

Any guidance on this? Thanks in advance!

I have this nice heavy winter coat that I accidentally tore a small hole in the shell near a chest pocket. It's a tiny rip, but I don't want it to get any larger. Any advice for how I should go about repairing it? I want to try a visible mend instead of a simple patch. The tag says the shell is listed as 61% cotton 39% nylon.

!Picture 1

!Picture 2

“Our philosophy is that if you can’t open it, you don’t own it. Once you disassemble, repair, and put back together your laptop or iPod, you have a much better understanding of what goes into it. It’s astounding how just 20 minutes of work can make an iPod good as new – but most people have no idea that there are instructions available to make the work easy. And why should they? Apple tells everyone that the battery isn’t user-serviceable.“

cross-posted from: https://slrpnk.net/post/3317096

> I bought this machine from the 1960s (cost: 12 Big Macs). I did not clean it or oil it as I wanted to just see if it works. > > It made a straight line without issue. Then on the 2nd straight line the top thread got bundled below the plate. I cleared that & started over. Then went to the narrowest zig-zag setting and the needle broke. > > I’m just starting to learn. I know from videos that pushing the fabric while the needle is down can bend the needle and put it in harms way. I don’t think I was pushing or pulling the fabric when the needle broke. So I wonder what would cause this-- does this mean the timing is off and needs adjustment? > > I’m not enthusiastic about doing much experimentation at this point because needles seem pricey enough that I don’t want to break many (1¼ the cost of a Big Mac in my area buys 5 needles). But I just removed the top thread and bobbin and installed the empty bobbin case. When I manually spin the wheel with no thread at various zig-zig widths, there is no apparent contact with the needle. So perhaps the thread occasionally bundling up under the plate is part of the issue. > > update: if I load thread and manually crank for the zig-zag patterns, most stitches are missed. The thread is plunged in from the top but does not get grabbed from the bottom most of the time.

I watched several sewing videos in preparation to buy a machine. The consensus is that drop-in bobbins are easier for beginners than front-load. Well I’m the kind of person who wants to get to the /expert/ stage & if that means doing things the hard way, so be it. But then the question is, what are the advantages of front-loads?

Youtube video id rbhfilt68vI titled “TESTED Best Sewing Machines for Beginners” suggests that front-load bobbins are more likely to get tangled and jammed. That sounds like an anti-feature for both beginners and experienced users. So why do front-load bobbin designs even exist?

(edit)

I think I got my answer. Video F7GTjrc-m5w says front-loading enables the machine to go faster and also enables you to switch bobbins mid-task.

I care more about jamming than speed. But the mid-task swapping sounds useful because I don’t suppose you can predict when it will run out. So I guess I need to consider how much stock to put into the comment about jamming.

I've recently started darning my worn-out socks (shoutout to that one poster who posted a tutorial) and so it's going really well! My socks are still comfy, and the woven patches do the job.

cross-posted from: https://slrpnk.net/post/2890733

> I think I need a sewing machine that can do a variety of different kinds of stitches. One use case is to repair holey socks by cannabalizing fabric from other holey socks. Thus the stitch needs to be the kind that can stretch and ideally not create an awkward feeling on the foot. > > Some sewing machines have a fixed number of stitches they can do. Would it make sense to get an embroidery machine and use #inkStitch (an Inkscape variant)? I’m not sure if that’s strictly for embroidery -- or does that give the ability to do a variety of stitches using FOSS? > > The inkstitch.org website steers people toward taking a basic sewing machine and modifying it using 3d printed parts. That’s too ambitious for me. I don’t want a hardware project. I just want to buy hardware that’s ready to go and use free software to control it. Is that possible with things that exist already?

This is an update to this post.

I turned the backpack inside out to see the damage on the inside. Most of the black plastic coating was gone, and you can see the patch I applied in the outside.

I decided to coat pretty much the entire bottom with Shoe Goo sealant, like I did in my last repair. This gave the material a lot of extra stiffness, as well as waterproofing it. You can see it applied in the shinier areas: !

Here is the sealant on the inside of the biggest rip, holding the patch in place: !

I know this update isn't particularly visually impressive, but it felt like a pretty successful fix. I'm looking forward to being able to use this bag again!

I've been looking for more adjustable closure ideas (excluding zippers and buttons) and ways to reduce my fabric cutting waste. This tutorial pointed me in the right direction!

This backpack has been stowed away at the back of my closet for a few months waiting to be fixed. It was being held together pretty tenuously: ! Sewed some of the smaller rips, then added repair tape to the largest one: !

Next step will be to turn it inside out and add some more material to the large rip. The entire bottom is pretty much thin enough to let light through at this point. I'll try to post an update once I fix that!

Zipper pull made from some shoelace I had lying around: !

Parts of the bottom of the bag were threadbare (literally starting to let light through). Gooped over everything with a bunch of Shoe Goo sealant, which turned out messy but effective: ! !

Overall I'm pretty please with how this turned out. Maybe not too pretty to look at, but thoroughly functional, and I'm sure it'll extend the life of this bag quite a bit

Glued and sewed a larger piece of gear repair tape to add fidelity to the ripped edge: ! Then sewed the rip itself with fishing line (the strongest thing I could think of to hold the weight of the bag's contents, plus I just happened to have it at home: !

As of this post, I've been using it for a week, and it's held up pretty well. I may add some sealant later to hold things in place.

Now all that's left to do is replace a missing zipper pull and fix some rodent damage to the front compartment... I may post about that at a later time

Basically the title. I would love to get at least a basic working knowledge of repairs and alterations, but I have no experience whatsoever. A “questions that don’t deserve their own post” or “starting resources” thing would be very helpful. Thank you!

I have this expensive*) suit which is a bit too baggy. I managed to slim down the trousers a bit and now they fit like a glove. But after watching countless videos about altering jackets, I decided to hand it to a tailor. No way I would to touch that.

*) I got it for cheap, second hand in great condition, but still it's one of those brands I could never afford brand new.

The small rip was patched with gear repair tape, then sewn over. The larger rip will probably be my next project... any recommendations to make sure it holds?

!

!

!

I have made a short video showing how I darn my socks, using a netting stitch rather than straight stitches.

It's the first time I've ever made a video & the stitiching is not the finest or neatest I have ever done, but I hope it shows the process well enough to follow.

This looks like a great resource for anyone in USA & Canada

This project is more stapling than sewing, but small upholstery projects are quite easy to do, and can be done with small amounts of fabric and padding. The padding for this project was mostly layers cut from an old quilt.

When you pull apart things like this you often find old repairs and layers of previous fabrics. It can be quite interesting to see the way they have been put together.

My feet are right at the top of most size ranges, which means I am constantly wearing holes in the toes. I have taken to darning the hole - or often sewing over the thinning patch to reinforce it before a hole wears through.

Whenever I see instructions for how to darn they use straight stiches like shown in this article, but I don't feel that having a solid patch in a stretchy fabric works well, so use a netting style stitch instead so it has more give. (when I get some time I might do some pics/a tutorial to show you).

Does anyone else darn their socks (or any other knitwear) and if so what type of stitch do you use?

I'm trying to create a bodice block/sloper. I feel bad going through so much calico but I know it will save time and fabric in the long run.

cross-posted from: https://sh.itjust.works/post/55504

> There is not really an outdoors/camping community I could find on Lemmy yet, so I thought nature was close! This is a cool site that shows you how you can make your own outdoors gear.

I often find holes wear in my jeans between the legs, so I patch them with fabric on the inside and lots of rows of zig-zag sewing.

!

It's not a very visible spot so it does not have to be perfect, but it definitely increases the useable life of the jeans considerably.

This little bag is one of my recent projects. I was gifting a couple of jars of homemade jam, so used an upholstery sample piece to make a bag.

The construction was quite simple, just sewing into a rectangle and then across the corners to make the shape. The stripes meant I didn't need to do any marking, just cut along the lines!

The straps were folded and sewn with a wide zig-zag stitch down the middle, as it is easier than methods involving turning and/or neatly placed straight stitching.

I have created this community to share projects and ideas with people who are interested in sewing and textile crafts made primarily from reclaimed and repurposed materials. That might be making bags from pillowcases, resewing a shirt into a child's dress, or repairing the hole in the knee of your jeans.

Feel free to share any projects you have made, or ask for questions or ideas for future projects.