Skip Navigation
Hyundai and Kia car thefts fall sharply after software upgrade, study finds
  • Well I mean actuaries are like savants. Years ago in uni my calc III college prof was one. Amazingly sharp dude. Do I think insurance companies over-generalize their risk assessments? Yupp. Do insurance companies likely ignore their actuaries and set premiums to make outrageous profit? Probably.

    Disclosure: I hate insurance companies. Also that professor was super weird

  • Hyundai and Kia car thefts fall sharply after software upgrade, study finds
  • It's funny that even though theft rates have plummeted since the mass software upgrade, premiums have stayed high. They have savant-level mathematicians (actuaries) evaluating risk and even with compelling data showing otherwise, they choose to keep labeling these cars high risk and continue to charge exorbitant premiums.

  • Do you think Hitler would have won WW2 if he hadn't invaded Russia?
  • Tik is a huge source of WWII misinformation? That's funny. I've watched tons of his WWII videos, they are excellent. His day-by-day series on Stalingrad is fantastic. Can you elaborate as to why you believe that? He agrees with the point that oil was a major driver for the invasion of the east. So is that statement misinformation too?

  • Tesla Cybertrucks Are Rusting Despite Being Made Of Stainless Steel
  • From Tesla's owners manual, referenced in the article:

    Immediately remove corrosive substances (such as grease, oil, tree resin, dead insects....

    I find it really funny that the folks at Tesla consider grease to be "corrosive".

  • Jupiter last night
  • I tried looking it up based on the current moon positions but couldn't find an answer. My best guess is it's a shadow of one of the four Galilean moons but I'm not sure which one

  • Jupiter last night

    This was my very first attempt at planetary imaging with my SCT6. I've been doing EAA work for a few years now, but mostly DSOs through the use of a Hyperstar. Last night I removed the Hyperstar from the rig and made my first attempts at imaging at the native 1500mm focal length.

    This was a 5 minute video processed with lucky sampling.

    6
    Anyone running 5/3/1 variations?
  • I know you asked this 3 months ago, but just wanted to give my two cents:

    I ran 5/3/1 for 6 years. I started at 27 and stopped it when I was 33. I saw huge gains with it and it was fun for a while. But it wasn't sustainable. Jim Wendler explicitly markets this program as one you can do forever. My experience completely contradicts this and your success with this program entirely depends on your age and quality of recovery. I would never recommend his program if you're not in your prime.

    After the spike in gains over the first two years, the constant push for PRs absolutely burned me out and left me bored. And then I ended up getting seriously hurt in a number of different ways. My body just couldn't take it anymore. I had to get shoulder surgery. Then I had to PT my knees. Then finally I fucked up my back in a way that won't ever fully recover.

    I spent a year going barely 1x/WK because I was so tired of the program and the intensity constantly aggravated old injuries. I finally got 100% back to the gym regularly, but I did so by throwing that 5/3/1 book away.

    I just want to look good naked. The old school thinking was that hypertrophy was hugely dependent on lifting low volume, heavy weight. More recent studies contradict this and show that high volume lower weight can have the same effect. So that's what I've chosen to do, my program focuses on this, I'm getting good gains in mass and I'm finally not leaving the gym in pain anymore.

    I guess what I'm saying is, use 5/3/1 and all variants at your own risk. It might be perfect for you depending on your goals & age, but consider a different approach to lifting if you want this to be a hobby you'll enjoy for many years to come.

  • Microsoft starts blocking ‘unauthorized’ Xbox controllers and accessories - The Verge
  • That sucks. The controller that came with my Xbox S randomly developed stick drift so bad it was trashed. I got maybe 10 hours of use out of it.

    I bought a third party controller with digital stick encoders to prevent the problem because Microsoft refuses to fix their controller design.

    Oh well guess I'm disabling console updates now

  • Home Improvement @lemmy.world WantsToPetYourKitty @lemmy.world
    Update: Rot behind soffit

    I made a post previously on having rot behind a soffit and many of you gave me great advice on how to proceed in fixing it the right way.

    This weekend I worked nonstop and got most of everything fixed. I removed part of soffit and cut the rafter tail to expose the area and quickly identified the problem - no kickout flashing !

    I cut out the rot on the sheathing and patched in plywood. ! I ripped the siding off all the way up to the roof to expose all the step flashing - this involved removing both the vinyl siding and the original composite siding. Working from the bottom upwards, I laid down new house wrap. I fabricated a nice piece of kick flashing to go on the end of the run.

    Then I installed a nice piece of counter flashing over the step flash, then finally another layer of house wrap partially overlapping the cFlash. !

    I then installed pressure treated furring strips ! for the vinyl siding and reinstalled the siding. Here's the siding going over my kickout flashing. !

    With that done I repaired the rafter tail and replaced all the rotten fascia board, then reinstalled the soffit vents.

    Now I'm in the process of installing drip edge before the gutter goes back. Due to poor roof installation, the underlayment doesn't extend down far enough to overlap my drip edge, so I'm having to cut 2.5" wide tarpaper strips and splice them in underneath the existing underlayment edge. That way the drip edge will be covered.

    5
    Leak and sheathing rot behind the end of a soffit. How do I fix this?
  • No diverter is present there at all. There's a bunch of things going on here that could be causing this problem and I think it would be best to address all of them at once:

    • No diverter
    • No drip edge present along gutter, and I've seen water drip from soffit vents. It's possible water is coming into the damaged area from where the soffit meets the wall
    • Vinyl siding was installed over original wood composite. It's questionable whether the step flashing is effective given the setup
    • Gutter potentially too small - I have to clean it out like 6 times a year even with gutter guards over most of it
  • Leak and sheathing rot behind the end of a soffit. How do I fix this?
  • Good point on the rafter tail. I'll look in the attic in that area to confirm.

    Yeah there's flashing above there and it's possible this is the source of the leak.

    I'm afraid what I'm going to have to do is take all the siding off above here to expose the flashing and inspect it and repair. Then to remove and fix the rot I'm gonna have to take everything apart to get into that area behind the soffit - remove the gutter, fascia, etc to gain proper access

  • Home Improvement @lemmy.world WantsToPetYourKitty @lemmy.world
    Leak and sheathing rot behind the end of a soffit. How do I fix this?

    Hey folks, looking for some advice because I don't know how to proceed.

    This house came with vinyl siding and I noticed rot under it. The rot terminates up high behind where this soffit meets with the exterior wall. I need to get in here to figure out how water is getting in and then make necessary repairs, but the soffit is really in the way.

    I've already removed the rot lower down - I had to remove vinyl siding, a layer of foam board, a layer of rotten OSB, the original rotten siding, and the original rotten sheathing. All of those layers are still present behind this soffit.

    When I take the soffit vent off, there's a layer of OSB directly above it. Really don't know how to gain access here.

    Any ideas?

    14
    Cleaned up someone else's mess (details in post)

    The chain sprocket here is supposed to rotate the keyed shaft below. At some point the 1/4" sq key came out. Instead of replacing the key, someone decided to try to just tighten the tiny set screw in the sprocket until it bottomed out on the keyway floor. It didn't end well and the keyway got trashed. !

    I cleaned up the keyway and installed a new key. !

    Then I milled a 1/4" slot into one half of a split shaft collar, and installed the collar over the part of the exposed key where the keyway in the shaft was damaged. Finally I installed a regular split shaft collar to butt against the end of the new key to keep it from backing out again. Final pic !

    4
    InitialsDiceBearhttps://github.com/dicebear/dicebearhttps://creativecommons.org/publicdomain/zero/1.0/„Initials” (https://github.com/dicebear/dicebear) by „DiceBear”, licensed under „CC0 1.0” (https://creativecommons.org/publicdomain/zero/1.0/)WA
    WantsToPetYourKitty @lemmy.world
    Posts 4
    Comments 26